File Size. Download Link. In , the sales volume of the unit in the US amounted to 85, vehicles a drop compared to - 0. In , Lincoln began shipping the machines to the Chinese market. Lincoln Motor Company was founded in in Detroit by Henry Liland, who previously founded Cadillac, for the production of aircraft engines. The company was named in honor of Abraham Lincoln, the 16th US president, for whom Leland voted in the first elections for himself.

Author:Gardam Arajind
Language:English (Spanish)
Genre:Personal Growth
Published (Last):22 February 2007
PDF File Size:6.80 Mb
ePub File Size:16.99 Mb
Price:Free* [*Free Regsitration Required]

Quick Links. Download this manual. Table of Contents. Ford motor company lincoln mkx quick reference guide 2 pages. Ford motor company lincoln town car owner's guide pages. Lincoln town car automobile owner's manual pages. Reproduction by any means, electronic or mechanical including photocopying, recording or by any information storage and retrieval system or translation in whole or part is not permitted without written authorization from Ford Motor Company. Read the following section on Warnings for a full explanation.

Indicates vehicle information related to recycling and other environmental concerns will follow. Correct vehicle usage and the authorized disposal of waste cleaning and lubrication materials are significant steps towards protecting the environment. Page 4: Instrumentation Instrumentation Panel dimmer switch pg. Page 5 Instrumentation Electronic sound system; refer to Audio Guide pg. Page 7 Instrumentation will usually be drivable and will not require towing.

Temporary malfunctions may cause your Service Engine Soon light to illuminate. Page 8 Instrumentation Light is blinking: Engine misfire is occurring which could damage your catalytic converter. You should drive in a moderate fashion avoid heavy acceleration and deceleration and have your vehicle serviced at the first available opportunity. Under engine misfire conditions, excessive exhaust temperatures could damage the catalytic converter, the fuel system, interior floor Page 9 Instrumentation parking brake indicates low brake fluid level.

Anti-lock brake system ABS Momentarily illuminates when the ignition is turned on and the engine is off. If the light remains on, continues to flash or fails to illuminate, have the system serviced immediately. Page 10 Instrumentation Engine oil pressure Illuminates when the oil pressure falls below the normal range. Stop the vehicle as soon as safely possible and switch off the engine immediately. Check the oil level and add oil if needed. Refer to Engine oil in the Maintenance and Care chapter.

Page 13 Instrumentation Safety belt warning chime Chimes to remind you to fasten your safety belts. For information on the safety belt warning chime, refer to the Seating and safety restraints chapter. Page 15 Instrumentation Speedometer Indicates the current vehicle speed. Page 18 Instrumentation to Compass calibration adjustment. Most geographic areas zones have a magnetic north compass point that varies slightly from the northerly direction on maps.

This variation is four degrees between adjacent zones and will become noticeable as the vehicle crosses multiple zones. Page 19 Instrumentation Compass calibration adjustment Perform this adjustment in an open area free from steel structures and high voltage lines. Start the vehicle. Page 21 Instrumentation 3. This current average measure will change as the speed control system changes the engine speed to maintain a constant vehicle speed. Page 22 Instrumentation not show the addition of fuel for a few kilometers miles.

Page 26 Controls and features Flash to pass Pull toward you to activate and release to deactivate. The selected temperature and the word AUTO will appear in the display window. The EATC system will either heat or cool to achieve the selected temperature.

The system will automatically determine fan speed, airflow location and if fresh outside air or recirculated air is required. The EATC will continue maximum cooling disregarding the displayed temperature until a warmer Page 29 Controls and features display. You can override fan speed at any time. To control fan speed manually, press the fan control to cancel automatic fan speed operation or use the AUTO Page 30 Controls and features clear water drips on the ground under the air conditioner drain while the system is working and even after you have stopped the vehicle.

Page 31 Controls and features mode. The air will be heated or cooled based on the temperature selection. For added customer comfort, the air distributed through the floor ducts will be slightly warmer than the air sent to the instrument panel registers. For short periods of time only, use this mode to prevent undesirable odors from entering the vehicle.

Page 33 Controls and features moving. The readings that you get may not agree with temperatures given on the radio due to differences in vehicle and station locations. This will prevent your windshield from fogging. Page 34 Controls and features reduce your ability to see through your windshield. Also, avoid placing small objects on top of your instrument panel. These objects can fall down into the defroster outlets and block airflow and possibly damage your climate control system.

Page 35 Controls and features Press the left control to decrease the time displayed. Hold the control while adjusting the wheel to the desired position, then release the control. The bars of varying length are for intermittent wipers. When in this position rotate the control upward for fast intervals and downward for slow intervals. Once speed control is switched off, the previously programmed set speed will be erased. For speed control to operate, the speed control must be ON and the vehicle speed must be This is normal.

Page 43 Controls and features When programming your HomeLink Universal Transmitter, you will be operating the garage door or gate. Be sure that people and objects are out to the way to prevent potential harm or damage. Do not use the HomeLink Universal Transmitter with any garage door opener that lacks safety stop and reverse features as Page 44 Controls and features 3.

Using both hands, press the hand-held transmitter control and the desired channel control on the HomeLink Universal Transmitter. Do not release the controls until step 4 has been completed.

Hold down both controls until the red light begins to flash slowly and then rapidly. To operate, simply press the appropriate channel control on the transmitter the red light will illuminate, indicating the signal is being transmitted. Page 46 Controls and features 3. Press the programmed HomeLink control in the vehicle until the training light on the garage door receiver turns solid seconds. Release the HomeLink control and repress to turn off the training light.

Press the HomeLink control again. To open the door, press the control located on the door. Depress again to stop window operation. To adjust your mirrors: 1. Select L to adjust the left mirror or R to adjust the right mirror. To program the memory seat to remote entry transmitter, refer to Remote entry system in the Controls and features chapter. Make sure that the mat does not interfere with the operation of the accelerator or the brake pedal.

Page 54 Controls and features Locking the doors Press this control to lock all doors. Page 55 Controls and features Opening the trunk Press the control once to open the trunk. Be certain the trunk is closed before driving your vehicle.

The trunk may appear closed, but it may not be latched. Failure to do so may cause objects to fall out of the trunk or block rear view vision. Page 56 Controls and features operating range will allow you to be up to 10 meters 33 feet away from your vehicle.

Page 57 Controls and features press any button on all transmitters up to four. When completed, switch the ignition to OFF. All transmitters must be programmed at the same time. Illuminated entry The interior lamps illuminate when the remote entry system is used to unlock the door s or sound the personal alarm.

With this feature, the first two programmed transmitters will recall a different memory position. Press the SET control. Press any button on the remote entry transmitter. Within five seconds, press the SET control again. Manually moving any seat or mirror during these steps will cancel the programming procedure. Page 61 Controls and features SecuriLock keys for more information.

If one or both of your SecuriLock keys are lost or stolen and you want to ensure the lost or stolen key will not operate your vehicle, bring your vehicle and all available SecuriLock keys to your dealership for reinitialization. Page 62 Controls and features procedure. If two previously programmed SecuriLock keys are not available one or both of your original keys were lost or stolen , you must bring your vehicle to your dealership to have the spare Page 63 Controls and features 3.


Lincoln Workshop Repair Manuals PDF



1998 Lincoln Town Car - Owner's Manual (188 pages)



Lincoln Town Car 1998 Owner's Manual



Lincoln Automobile Manuals


Related Articles